Memory Controller/PHY IP for UMC
Welcome to the ultimate
Memory Controller/PHY IP
for
UMC
hub! Explore our vast directory of
Memory Controller/PHY IP
for
UMC
All offers in
Memory Controller/PHY IP
for
UMC
Filter
Compare
181
Memory Controller/PHY IP
for
UMC
from
6
vendors
(1
-
10)
-
Serial ATA (SATA) PHY Transceiver IP
- SMS6000 is a fully integrated CMOS transceiver that handles the low level Serial ATA protocol and signaling.
- It contains all necessary Clock synthesis, Clock Recovery, Serializer, Deserializer, Comma detect for 8B/10B encoded data and Frame alignment functionalities.
-
DDR4 multiPHY - UMC 28HPC18
- Support for JEDEC standard DDR4, DDR3, LPDDR2, and LPDDR3 SDRAMs
- Scalable architecture that supports data rates up to DDR4-2667
- Support for DIMMs
- Delivery of product as a hardened mixed-signal macrocell component allows precise control of timing critical delay and skew paths
-
LPDDR4 multiPHY V2 - UMC 28HPC+18
- Supports JEDEC standard LPDDR4X, LPDDR4, LPDDR3, DDR4, DDR3, and DDR3L (1.35V DDR3) SDRAMs
- Support for data rates up to 4,267 Mbps (process dependent)
- Designed for rapid integration with Synopsys Enhanced Universal DDR Memory/Protocol Controllers (uMCTL2/uPCTL2) for a complete DDR interface solution
- PHY independent, firmware-based training using an embedded calibration processor
-
ONFI IO v3.2, 533MT/s, UMC40LP
- Supports ONFI 6.0(4.8Gbps), ONFI 5.1(3.6Gbps), ONFI 5.0(2.4Gbps), ONFI 4.1(1.2Gbps), ONFI 4.0(800Mbps) & ONFI 3.2(533Mbps)
- Power-sequence free
- Provides multi-driving-strength selection
- Provides CTT mode and LTT mode
-
ONFI IO v3.2, 533MT/s, UMC 28HPC+, 1.8V, N/S orientation, H&V cell
- Supports ONFI 6.0(4.8Gbps), ONFI 5.1(3.6Gbps), ONFI 5.0(2.4Gbps), ONFI 4.1(1.2Gbps), ONFI 4.0(800Mbps) & ONFI 3.2(533Mbps)
- Power-sequence free
- Provides multi-driving-strength selection
- Provides CTT mode and LTT mode
-
ONFI IO v4.0, 800MT/s, UMC 28HPC+, 1.8V, N/S orientation, H&V cell
- Supports ONFI 6.0(4.8Gbps), ONFI 5.1(3.6Gbps), ONFI 5.0(2.4Gbps), ONFI 4.1(1.2Gbps), ONFI 4.0(800Mbps) & ONFI 3.2(533Mbps)
- Power-sequence free
- Provides multi-driving-strength selection
- Provides CTT mode and LTT mode
-
ONFI IO v4.1, 1.2T/s, UMC 22ULL, 1.8V, N/S orientation, H&V cell
- Supports ONFI 6.0(4.8Gbps), ONFI 5.1(3.6Gbps), ONFI 5.0(2.4Gbps), ONFI 4.1(1.2Gbps), ONFI 4.0(800Mbps) & ONFI 3.2(533Mbps)
- Power-sequence free
- Provides multi-driving-strength selection
- Provides CTT mode and LTT mode
-
SATA 6G PHY in UMC (40nm, 28nm, 22nm)
- Compliant with SATA/eSATA v3.3, AHCI v1.3 and SATA PIPE v4.3 specifications
- AMBA 2.0 AHB and AMBA 3 AXI subsystem interfaces
- AMBA 4 AXI and ACE-Lite bus interfaces
- Memory data protection and memory address parity protection