USB 3.1 Controller IP

Compare 22 USB 3.1 Controller IP from 6 vendors (1 - 10)

USB 3.1 Cable Marker IP
- USB PD 3.1 compliant.
- Single chip solution – just two external capacitors.
- 4 pin package.
- Less than 1mm2 area in 180nm.
- PROM programmed through vendor message protocol.
- Based on Obsidian’s mature PD technology.
- Integrated PROM enables customized response to a wide range of vendor requirements.
- Active Ra pulls down only requires 10uA at 5V., but is <1K below 2V.
- Power <5mW. Enabled by CC data activity. I.e. very low duty cycle.
- Programming can be done after assembly into the cable. Fuse lock function.
- Supports low cost, 4 layer PCB assembly.
Complete USB Type-C Power Delivery IP
- Mixed signal Analog Front End Macros for 65n, 130n, 150nm, and 180n technologies.
- RTL code from AFE to I2C compatible register set.
- Stand alone C code for Protocol, Device Policy Manager, and System Policy Manager.
- IP demonstration & development board, with compliance reports.
- Full chip integration of USB Type-C, and associated software.
eUSB 3.1 Gen 2 Device Controller - Software Enumeration, FIFO Interface
- Software Enumeration
- FIFO Interface
USB 3.1 Host Premium
- Supports SuperSpeed USB power savings modes, Uniform Power Format (UPF) and dual power rails
- Configurable data buffering options to optimize performance vs area
- Lowers overall system power by design
- Supports SuperSpeed and High-Speed modes
USB 3.1 DRD Premium
- Supports SuperSpeed USB power savings modes, Uniform Power Format (UPF) and dual power rails
- Configurable data buffering options to optimize performance vs area
- Lowers overall system power by design
- Supports SuperSpeed and High-Speed modes
SuperSpeed USB 3.1 Host Controller Multiport
- Supports SuperSpeed USB power savings modes, Uniform Power Format (UPF) and dual power rails
- Configurable data buffering options to optimize performance vs area
- Lowers overall system power by design
- Supports SuperSpeed and High-Speed modes
SuperSpeed USB 3.1 Host Controller
- Supports SuperSpeed USB power savings modes, Uniform Power Format (UPF) and dual power rails
- Configurable data buffering options to optimize performance vs area
- Lowers overall system power by design
- Supports SuperSpeed and High-Speed modes
SuperSpeed USB 3.1 DRD Controller
- Supports SuperSpeed USB power savings modes, Uniform Power Format (UPF) and dual power rails
- Configurable data buffering options to optimize performance vs area
- Lowers overall system power by design
- Supports SuperSpeed and High-Speed modes
SuperSpeed USB 3.1 Device Controller
- Supports SuperSpeed USB power savings modes, Uniform Power Format (UPF) and dual power rails
- Configurable data buffering options to optimize performance vs area
- Lowers overall system power by design
- Supports SuperSpeed and High-Speed modes
USB 3.1 Gen1 / Gen2 Host Controller IP
- USB 3.1 Host Controller can be configured to support all types of USB transfers – Bulk, Interrupt and Isochronous.
- Allows dynamic configuration to support configurable number of endpoints, interfaces, alternate interfaces and configurations.
- USB 3.1 Host Controller can be configured to support any combinations of USB 3.1 interface speeds – SSP (10 Gbps), SS(5 Gbps), HS (480 Mbps), FS(12 Mbps) and LS(1.5 Mbps). Eg combinations are SSP & SS only, SSP & SS & HS only, SSP & SS & HS & FS only, SS Only, SS & HS Only, SS & HS & FS Only, HS & FS Only etc.
- USB 3.1 Host Controller has full support for all low power features of the USB Specification supporting Suspend and Remote Wakeup, USB 3.1 Low Power States – U1/U2/U3 and USB 2.0 Link Power Management states – L1, L2.