USB 3.0/3.1/3.2/SSIC Verification IP

USB 3.0/3.1/3.2 Verification IP provides a smart way to verify the USB 3.0/3.1/3.2 component of a SOC or a ASIC. It provides backward compatibility support for earlier versions 3.0,3.1 and 3.2 of USB specifications. The SmartDV's USB 3.0/3.1/3.2 Verification IP is fully compliant with standard USB Specification 3.0/3.1/3.2. The USB 3.0/3.1/3.2 VIP can be readily customized and optimized for a wide range of specific system applications.

USB 3.0/3.1/3.2/SSIC Verification IP is supported natively in SystemVerilog, VMM, RVM, AVM, OVM, UVM, Verilog, SystemC, VERA, Specman E and non-standard verification env

USB 3.0/3.1/3.2/SSIC Verification IP comes with optional Smart Visual Protocol Debugger (Smart ViPDebug), which is GUI based debugger to speed up debugging.

• Compliant with USB 3.0/3.1/3.2 specification version 1.0
• Supports Superspeed USB 3.0, SuperSpeedPlus 3.1 , USB 3.2 and 3.0 OTG
• Complete solution for thorough chip-level verification
• Comprehensive model support a Host, Device, Hub, PHY
• Configurable number of Configurations, Interfaces, Alternative Interfaces and Endpoints
• Supports constrained randomization of protocol attributes
• Supports all types of error injection and detection
• Supports error injection in all the layers of USB 3.0/3.1/3.2
• USB 3.0/3.1/3.2 Common support
• Configurable PHY Interface width 8, 16 or 32 bits
• PHY interface supports data scrambling to reduce EMI emissions
• Comprehensive compliance testsuite for Protocol, Link, and Physical layer verification
• Supports Low frequency periodic signaling (LFPS) for initialization and power management(U1, U2 & U3)
• Supports Interrupt/Bulk/Isochronous/Control Transfers
• Control transfers supported by Endpoint 0
• Separate Endpoint Buffers for IN bound and OUT bound packets
• Supports for USB 3.0/3.1/3.2 low power states
• Bulk Stream support
• Supports Lane polarity inversion
• Supports eXtensible Host Controller Interface
• USB 3.0 support
• Compliant with USB 3.0 specification.
• Compliant with USB 3.0 Super speed Inter chip supplement 1.0.
• USB 3.0 host and device with SERIAL/PIPE/SSIC interfaces
• Supports dual-simplex, four-wire differential signaling and 8b/10b parallel interface
• Operates at Super speed (5 Gbit/s), High(480 Mbit/s) or Full speed(12 Mbit/s) modes
• Supports SS-OTG,SSPC-OTG Devices,SS-PO Devices and SS-EH Devices
• Supports ADP,HNP,SRP and RSP
• USB 3.0 host and device with SERIAL/PIPE/SSIC interfaces
• Supports Inter-Chip Supplement to the USB Revision 3.0 Specification (Super Speed Inter-Chip) using MIPI MPHY
• Supports MPHY Type-I operations
• Supports MPHY all PWM 1 gear of operation
• Supports MPHY all HS 1,2,3 gear of operation
• Supports 1,2,4 lanes
• Supports all types of error injection in MPHY
• Supports All RRAP Packet types
• Supports LS and HS burst
• Supports all LS and HS gears
• Supports all protocol error detection
• Supports all MPHY protocol error injection
• Supports RMMI and MPHY serial interface
• Supports UTMI and PIPE interfaces.
• USB 2.0 device and host with UTMI/ULPI interfaces.
• Supports all types of error injection and detection.
• Supports error injection in all the layers of USB 3.0.
• Supports constrained randomization of protocol attributes.
• On-the-fly protocol and data checking.
• Notifies the testbench of significant events such as transactions, warnings, timing and protocol violations.
• Built in coverage analysis.
• Callbacks in host and device for various events.
• Status counters for various events.
• USB 3.0/3.1 Verification IP comes with complete testsuite to test every feature of USB 3.0/3.1 specification.
• xHCI support
• USB 3.0 OTG
• Supported devices.
• 1.SS-OTG
• 2.SSPC-OTG Devices
• 3.SS-PO Devices
• 4.SS-EH Devices
• Support for USB 2.0.
• 1.SS-OTG or SSPC-OTG devices operate as USB 2.0 OTG devices.
• 2.SS-EH operate as USB 2.0 EH.
• 3.SS-PO operate as USB 2.0 PO devices.
• Supported protocols.
• 1.SRP
• 2.HNP
• 3.ADP
• 4.RSP for USB 3.0
• Supported speeds.
• 1.SS,HS and FS
• Supported feature selector
• 1.b_hnp_enable
• 2.a_hnp_support
• 3.a_alt_hnp_support
• 4.NTF_HOST_REL
• 5.B3_RSP_ENABLE
• Support the all timeout condition
• 1.a_wait_vfall_timout
• 2.a_wait_vrise_timout
• 3.a3_polling_tmout
• 4.a3_recovery_tmout
• 5.a3_rx_detect_active_tmout
• 6.rsp_cnf_err_tmout
• 7.rsp_ack_err_tmout
• 8.rsp_wrst_err_timout
• 9.b3_polling_tmout
• 10.b3_recovery_tmout
• 11.b3_rx_detect_active_tmout
• Combination of SSPC-OTG device communication
• 1.SSPC-OTG device to SSPC-OTG device
• 2.SSPC-OTG device to SS-OTG device
• 3.SS-OTG device to SSPC-OTG device
• 4.SSPC-OTG device to USB 2.0 OTG
• 5.USB 2.0 OTG device to SSPC-OTG device
• USB 3.1 support
• Compliant with USB 3.1 specification version 1.0
• Supports dual-simplex, four-wire differential signaling and 128b/132b parallel interface
• Operates at SuperSpeedPlus (10 Gbit/s), Super speed (5 Gbit/s), High speed(480 Mbit/s) or Full speed(12 Mbit/s) modes
• Backward compatible with USB 3.0
• USB 3.1 host and device with SERIAL/PIPE interfaces
• Supports specific LFPS patterns(SCD1/SCD2) for Super speed plus ports
• Supports SuperSpeedPlus LFPS Based PWM Message (LBPM)
• Supports SuperSpeedPlus Precision Time Measurement
• Supports SuperSpeedPlus Transaction Reordering for periodic and asynchronous packets
• USB 3.2 support
• Supports dual-lane for Gen1 and Gen2
• Backward compatible with USB 3.1 and USB 3.0
• USB 3.2 host and device with dual-lane SERIAL/PIPE interface
• Supports Deskew
• Supports Data striping in dual lanes
• Supports dual-simplex, four wire differential signaling and 128b/132b parallel interface
• Supports Configuration summary descriptor
• Support Retimer connectivity models
• Supports all the Retimer state machine states[RTSM]
• Supports SRIS and Bit-Level Retimers functionality
• Supports Retimer presence announcement through LBPM

• Rich set of configuration parameters to control the functionality
• Faster testbench development and more complete verification of USB 3.0/3.1/3.2 designs.
• Easy to use command interface simplifies testbench control and configuration of host and device.
• Simplifies results analysis.
• Runs in every major simulation environment.

• Complete regression suite containing all the USB 3.0/3.1/3.2 testcases.
• Examples showing how to connect various components, and usage of BFM and Monitor.
• Detailed documentation of all class, task and function's used in verification env.
• Documentation also contains User's Guide and Release notes.