MIPI CSI-2 Transmitter IIP

MIPI CSI-2 Transmitter interface provides full support for the two-wire MIPI CSI2 serial interface, compatible with MIPI CSI-2 Specification version 2.1. It is typically residing in a camera module and provides communication to MIPI CSI-2 receiver in an image application processor over the serial PHY link. MIPI CSI-2 Transmitter IIP is fully configurable and proven in FPGA environment. The host interface of the MIPI CSI-2 can be simple interface or can be AMBA APB, AMBA AHB, AMBA AHB-Lite, AMBA AXI, AMBA AXI-Lite, VCI, OCP, Avalon, PLB, Tilelink, Wishbone or Custom protocol.

MIPI CSI-2 Transmitter IIP is supported natively in Verilog and VHDL

• Compliant with MIPI CSI-2 Specification v1.0, v1.1, v1.3, v2.0,v2.1
• Compliant with D - PHY Specification v1.1,v1.2,v2.0,v2.1
• Compliant with C - PHY Specification v0.7,v1.2,v2.0
• Full MIPI CSI-2 TRANSMITTER functionality where either D - PHY / C - PHY can be used
• Supports Multi lane distribution and also lanes can be configured up to 4 lanes for C - PHY and 8 lanes for D - PHY
• Supports Data rate up to 4.5 Gbps per data lane of D – PHY. 36 Gbps in 8 Lanes
• Supports Data rate up to 3 Gsps per trio using C – PHY. 17 Gbps in 3 Trios
• Supports up to 4 Virtual channels
• Supports continuous and non-continuous clock modes
• Supports PPI Interface to connect to C - PHY / D - PHY
• Supports Short and Long packets
• Supports Frame and Line Synchronization Packets (Short Packets)
• Supports Data Scrambling in Lanes.
• Supports High Speed and Escape Mode (LPDT and ULPS) Transmission.
• Supports various methods to interleave the transmission of different image data formats
• Data type
• Virtual channel
• Supports Image applications with varying Pixel formats
• RAW Data Type - RAW6, RAW7, RAW8, RAW10, RAW12, RAW14, RAW16, RAW20, RAW24
• RGB Data Type - RGB444, RGB555, RGB565, RGB888, RGB 666
• YUV Data Type - YUV422-8bit, YUV422-10bit, YUV420-8bit, YUV420-10bit, Legacy YUV420-8bit
• User Defined data type – 8-bit
• Generic 8-bit long packets (Null, Blanking, Embedded data)
• Multiple video formats with up to four pixels per pixel clock
• Supports Video Stream Interface at Pixel Level
• Interrupt support for indicating internal status/error information.
• Supports ALPS (Alternate Low Power State) in C- PHY mode.
• Supports Latency Reduction and Transport Efficiency (LRTE)
• Fully synthesizable
• Static synchronous design
• Positive edge clocking and no internal tri-states
• Scan test ready
• Simple interface allows easy connection to microprocessor/microcontroller devices

• Single Site license option is provided to companies designing in a single site.
• Multi Sites license option is provided to companies designing in multiple sites.
• Single Design license allows implementation of the IP Core in a single FPGA bitstream and ASIC.
• Unlimited Designs, license allows implementation of the IP Core in unlimited number of FPGA bitstreams and ASIC designs.

• The MIPI CSI-2 Transmitter interface is available in Source and netlist products
• The Source product is delivered in verilog. If needed VHDL, SystemC code can also be provided.
• Easy to use Verilog Test Environment with Verilog Testcases
• Lint, CDC, Synthesis, Simulation Scripts with waiver files
• IP-XACT RDL generated address map
• Firmware code and Linux driver package
• Documentation contains User's Guide and Release notes.