Vendor: Rambus, Inc. Category: MACsec

MACsec Engine optimized for 10Base-T1S/T1L applications

Full line rate and smallest size MACsec solution for 10M ports with MII interface

FIPS 140.3 IEEE 802.1AE + 2 View all specifications

Overview

10Base-T1S is a standard for a 10Mbit/s single-pair Ethernet over an unshielded, single-twisted pair that was introduced with the IEEE 802.3cg-2019 specification. It brings Ethernet technology into the low-cost, edge applications space, enabling connection of “edge nodes” (remote sensors, actuators, light controls, etc.) to a “head node” (host MCU, switch or gateway) using a multi-drop bus up to 25 meters in length.

The T1S physical wires are located at remote locations, like peripheral zones, and are easily accessible for potential physical intervention, where the attacker may not only read the data, but also inject its own. Therefore, protecting T1S traffic is vitally important, and IEEE802.1AE MACsec has been chosen as an industry-wide network security protocol for this purpose.

How the MACsec-IP-360 works

The MACsec-IP-360 engine provides complete MACsec processing for a port. It contains programmable matching rules for the uncontrolled and controlled (MACsec) processing. It supports multiple SecY (CA).

All features and ciphers of the standard MACsec are supported. The processing results are reflected in the MACsec statistics and additional non-standard counters. The MACsec-IP-360 engine operates as a fixed delay component at the MII side, preserving accuracy of PTP timestamping and TSN scheduling created by the TSN MAC subsystem. Its operation is transparent for non-packet related information that is sent over the MII bus.

Key features

Packet Interface

  • Cut-through FIFO interface with frame interleaving for IEEE802.3br
  • 128-bit wide
  • External classification inputs
  • SOP and EOP pass-through bus for side-band information
  • Lowest and fixed-latency modes

SA and classification scaling

  • SA (16 to 256)
  • TCAM rules (16 to 512)

Control Interface

  • Simple 32-bit interface
  • Interrupts

Protocol Support

  • Full IEEE 802.1AE-2018 compliance
  • IEEE 802.1AE
  • IEEE 802.1AEbn
  • IEEE 802.1AEbw
  • IEEE 802.1AEcg
  • MACsec with up to 4x VLAN-in-clear

NIST CAVP Compliance for FIPS 140-3 Validation

  • Basic AES-ECB/CTR/AES-GCM transformations

Block Diagram

Benefits

  • MACsec solution for integration between MAC and PCS/PLCA modules at the MII side of an Ethernet subsystem.
  • Fully-compliant MACsec solution supporting 10M full and half-duplex rates and supports VLAN-in-clear case.
  • Full IEEE 802.1AE-2018 and Open Alliance Automotive MACsec profile support.

What’s Included?

Packages

  • Silicon IP
  • Driver Development Kit

Complete Documentation

  • Hardware integration guide
  • Hardware and software reference manuals
  • Programming guides
  • IP-XACT Register description

 

Tools and Scripts

  • Verilog for synthesis and simulation
  • All scripts and support files needed for standard EDA tool flows

Verification Support

  • Complete verification test bench
  • Comprehensive test vectors

Integration Support

  • Complete verification test bench
  • Comprehensive set of test vectors

Specifications

Identity

Part Number
MACsec-IP-360
Vendor
Rambus, Inc.
Type
Silicon IP

Security

MACsec Standard
IEEE 802.1AE , IEEE 802.1AEbn , IEEE 802.1AEbw

Safety & Qualification

Security Certification
FIPS 140.3

Files

Note: some files may require an NDA depending on provider policy.

Provider

HQ: USA

Learn more about MACsec IP core

Extending Ethernet Security to the Automotive Edge

Ethernet is becoming the communications backbone of the software-defined vehicle. What began with high-bandwidth connections between central compute, domain controllers and advanced sensors is now extending much further toward the edge.

Beyond Trusted: What the NSA’s New Guidance Means for Hardware Security

On August 25, 2026, the National Security Agency (NSA) released two technical reports addressing intentional threats to application-specific integrated circuits during design and manufacturing: the “ASIC Best Practices Threat Catalog” and “Application Specific Integrated Circuit Level of Assurance 1 (LoA1) Best Practices”.

Frequently asked questions about MACsec IP cores

What is MACsec Engine optimized for 10Base-T1S/T1L applications?

MACsec Engine optimized for 10Base-T1S/T1L applications is a MACsec IP core from Rambus, Inc. listed on Semi IP Hub.

How should engineers evaluate this MACsec?

Engineers should review the overview, key features, supported foundries and nodes, maturity, deliverables, and provider information before shortlisting this MACsec IP.

Can this semiconductor IP be compared with similar products?

Yes. Buyers can compare this product with similar semiconductor IP cores or IP families based on category, provider, process options, and structured technical specifications.

×
Semiconductor IP