What is UART DO-254 IP Core?
UART DO-254 IP Core is a UART IP core from SafeCore Devices listed on Semi IP Hub.
Vendor:
SafeCore Devices
Category:
UART
UART DO-254 IP Core
The Universal Asynchronous Receiver/Transmitter (UART) is a hardware device that translates data between parallel and serial form…
Overview
The Universal Asynchronous Receiver/Transmitter (UART) is a hardware device that translates data between parallel and serial forms. UARTs are commonly used in conjunction with communication standards such as TIA (formerly EIA) RS-232, RS-422 or RS-485. The universal designation indicates that the data format and transmission speeds are configurable. The electric signaling levels and methods (such as differential signaling etc.) are handled by a driver circuit external to the UART.
The UART IP Core has been developed to DAL A according to the DO-254 / ED-80 and is accompanied by a Certification Kit. For lower DAL levels reduced documentation sets are available. The core is also available as a netlist for DAL D or projects not needing the full RTL source.
Implementation Details
Unless otherwise specified all the runs have been performed with the default options of the respective tool. Register placement on the IO has been disabled.
No constraints were added, so the results listed under the column “Maximum frequency of operation” are the worst case scenario (no multicycle, false paths, etc. defined).
The results are provided for an UART Core with the following configuration generics (see Table 1):
- ‘g_ASYNC_INPUT’ – TRUE
- ‘g_CLOCK_DIVIDER’ – 139
- ‘g_DATA_WIDTH’ – 8
- ‘g_PARITY_ENABLE’ – ‘1’
- ‘g_ODD_PARITY’ – ‘0’
- ‘g_2_STOP_BITS’ – ‘1’
and without TMR (Triple Module Redundancy), if TMR is used the number of registers will be triplicated, the combinatorial logic will also increase and there might be a penalty on the maximum ‘clk’ frequency.
ACTEL / MICROSEMI
| FPGA Type | Maximum ‘clk‘ Frequency | Logic Modules (CORE) |
|---|---|---|
| ProASIC3
(A3P015 68QFN I Std) |
132 MHz | 163 |
| IGLOO
(AGL030V5 100VQPF I Std) |
127 MHz | 163 |
| Fusion
(AFS090 180QFN I Std) |
132 MHz | 163 |
| Axcelerator
(RTAX250S 208CQFP Mil Std) |
141 MHz | SEQUENTIAL (R-cells): 63
COMB (C-cells): 74 |
ALTERA
| FPGA Type | Maximum ‘clk’ Frequency | Flip-Flops | ALUTs | ALMs | Logic Cells |
|---|---|---|---|---|---|
| MAX II
(EPM240F100I5) |
127 MHz | 57 | – | – | 83 |
| Cyclone III
(EP3C5E144I7) |
> 340 MHz | 57 | – | – | 83 |
| Stratix II
(EP2S60F484I4) |
> 420 MHz | 59 | 66 | 42 | – |
| Stratix III
(EP3SE110F780I3) |
> 550 MHz | 57 | 63 | 41 | – |
| Stratix IV
(EP4SGX70HF35C2) |
> 670 MHz | 58 | 64 | 41 | – |
XILINX
| FPGA Type | Maximum ‘clk‘ Frequency | Flip-Flops | 4-LUTs | Slices | Macrocells |
|---|---|---|---|---|---|
| CoolRunnerII
(XC2C128-6-TQ144) |
126 MHz | 57 | – | – | 58 |
| Spartan3
(XC3S50-4PQ208) |
189 MHz | 56 | 91 | 53 | – |
| Virtex2
(XC2V40-4FG256) |
174 MHz | 56 | 90 | 53 | – |
| Virtex4
(XC4VLX15-12SF363) |
> 460 MHz | 56 | 92 | 53 | – |
| Virtex5
(XC5VLX30-3FF324) |
> 390 MHz | 56 | – | 35 | – |
Key features
- Design Assurance Level A according to RTCA DO-254/ED-80 (April, 2000)
- Configurable baud rate, number of data bits, parity and stop bits.
- Fully deterministic handshake interface that allows easy handling of reception/transmission requests
- Single clock domain fully synchronous design
- Interface to standard RS-232 drivers, so it can be used without modification in standard hardware
- Simple interface to user’s logic
- TMR coded for SEU immunity (optional)
- Technology independent (can be synthesized to any FPGA/CPLD vendor)
Block Diagram
UART DO-254 IP Core block diagram
Specifications
Identity
Part Number
UART DO-254 IP Core
Vendor
SafeCore Devices
Type
Silicon IP
Files
Note: some files may require an NDA depending on provider policy.
Provider
HQ:
Spain
Frequently asked questions about UART IP cores
How should engineers evaluate this UART?
Engineers should review the overview, key features, supported foundries and nodes, maturity, deliverables, and provider information before shortlisting this UART IP.
Can this semiconductor IP be compared with similar products?
Yes. Buyers can compare this product with similar semiconductor IP cores or IP families based on category, provider, process options, and structured technical specifications.