MIPI CSI-2 Transmitter IP
Overview
MIPI CSI-2 Transmitter interface provides full support for the two-wire MIPI CSI2 serial interface, compatible with MIPI CSI-2 Specification version 2.1. It is typically residing in a camera module and provides communication to MIPI CSI-2 receiver in an image application processor over the serial PHY link. MIPI CSI-2 Transmitter IIP is fully configurable and proven in FPGA environment. The host interface of the MIPI CSI-2 can be simple interface or can be AMBA APB, AMBA AHB, AMBA AHB-Lite, AMBA AXI, AMBA AXI-Lite, VCI, OCP, Avalon, PLB, Tilelink, Wishbone or Custom protocol.
Key Features
- Compliant with MIPI CSI-2 Specification v1.0, v1.1, v1.3, v2.0,v2.1
- Compliant with D - PHY Specification v1.1,v1.2,v2.0,v2.1
- Compliant with C - PHY Specification v0.7,v1.2
- Full MIPI CSI-2 TRANSMITTER functionality where either D - PHY / C - PHY can be used
- Supports Multi lane distribution and also lanes can be configured up to 4 lanes for C - PHY and 8 lanes for D - PHY
- Supports Data rate up to 4.5 Gbps per data lane of D ��ô PHY. 36 Gbps in 8 Lanes
- Supports Data rate up to 3 Gsps per trio using C ��ô PHY. 17 Gbps in 3 Trios
- Supports up to 4 Virtual channels
- Supports continuous and non-continuous clock modes
- Supports PPI Interface to connect to C - PHY / D - PHY
- Supports Short and Long packets
- Supports Frame and Line Synchronization Packets (Short Packets)
- Supports Data Scrambling in Lanes.
- Supports High Speed and Escape Mode (LPDT and ULPS) Transmission.
- Supports various methods to interleave the transmission of different image data formats
- -> Data type
- -> Virtual channel
- Supports Image applications with varying Pixel formats
- -> RAW Data Type - RAW6, RAW7, RAW8, RAW10, RAW12, RAW14, RAW16, RAW20, RAW24
- -> RGB Data Type - RGB444, RGB555, RGB565, RGB888, RGB 666
- -> YUV Data Type - YUV422-8bit, YUV422-10bit, YUV420-8bit, YUV420-10bit, Legacy YUV420-8bit
- -> User Defined data type ��ô 8-bit
- -> Generic 8-bit long packets (Null, Blanking, Embedded data)
- Multiple video formats with up to four pixels per pixel clock
- Supports Video Stream Interface at Pixel Level
- Interrupt support for indicating internal status/error information.
- Supports ALPS (Alternate Low Power State) in C- PHY mode.
- Fully synthesizable
- Static synchronous design
- Positive edge clocking and no internal tri-states
- Scan test ready
- Simple interface allows easy connection to microprocessor/microcontroller devices
Benefits
- Single Site license option is provided to companies designing in a single site.
- Multi Sites license option is provided to companies designing in multiple sites.
- Single Design license allows implementation of the IP Core in a single FPGA bitstream and ASIC.
- Unlimited Designs, license allows implementation of the IP Core in unlimited number of FPGA bitstreams and ASIC designs.
Deliverables
- The MIPI CSI-2 Transmitter interface is available in Source and netlist products
- The Source product is delivered in verilog. If needed VHDL, SystemC code can also be provided.
- Easy to use Verilog Test Environment with Verilog Testcases
- Lint, CDC, Synthesis, Simulation Scripts with waiver files
- IP-XACT RDL generated address map
- Firmware code and Linux driver package
- Documentation contains User s Guide and Release notes.
Technical Specifications
Maturity
Getting used at customer site
Related IPs
- MIPI CSI-2 Receiver
- MIPI D-PHY IP for TSMC (5nm, 6/7nm, 12/16nm, 22nm, 28nm, 40nm)
- Multi-Video-Source Multiplexing Serial Video Transmitter for MIPI CSI2
- MIPI D-PHY CSI-2 TX (Transmitter) in TSMC 40LP
- MIPI C-PHY-D-PHY Combo PHY IP on TSMC 28nm HPC+
- MIPI C-PHY/D-PHY Combo CSI-2 TX (Transmitter) IP in TSMC 65LP